AMD GPU: Difference between revisions

From NixOS Wiki
imported>Lucasew
No edit summary
imported>Lelgenio
Fix instructions for blender HIP, generic instructions are not sufficient, there's also a dedicated package for it.
Line 30: Line 30:


== HIP ==
== HIP ==
Software like Blender may support HIP for GPU acceleration. Most software has the HIP libraries hard-coded. You can work around it on NixOS by using:
Most software has the HIP libraries hard-coded. You can work around it on NixOS by using:


<syntaxhighlight lang="nix">
<syntaxhighlight lang="nix">
Line 38: Line 38:
</syntaxhighlight>
</syntaxhighlight>


This was tested and working with Blender 3.3 from blender-bin and a Ryzen 5600G with no dedicated graphics.
=== Blender ===
 
Hardware accelerated rendering can be achieved by using the package <syntaxhighlight lang="nix" inline>blender-hip</syntaxhighlight>.


== OpenCL ==
== OpenCL ==

Revision as of 03:30, 22 July 2023

This guide is about setting up NixOS to correctly use your AMD Graphics card if it is relatively new (aka, after the GCN architecture).

Make the kernel use the correct driver early

The kernel can load the correct driver right away:

boot.initrd.kernelModules = [ "amdgpu" ];

XServer

Make sure Xserver uses the `amdgpu` driver in your configuration.nix:

services.xserver.enable = true;
services.xserver.videoDrivers = [ "amdgpu" ];

Enable Southern Islands (SI) and Sea Islands (CIK) support

The oldest architectures that AMDGPU supports are Southern Islands (SI, ie. GCN 1) and Sea Islands (CIK, ie. GCN 2), but support for them is disabled by default. To use AMDGPU instead of the radeon driver, you can set the kernel parameters:

# for Southern Islands (SI ie. GCN 1) cards
boot.kernelParams = [ "radeon.si_support=0" "amdgpu.si_support=1" ];
# for Sea Islands (CIK ie. GCN 2) cards
boot.kernelParams = [ "radeon.cik_support=0" "amdgpu.cik_support=1" ];

HIP

Most software has the HIP libraries hard-coded. You can work around it on NixOS by using:

systemd.tmpfiles.rules = [
    "L+    /opt/rocm/hip   -    -    -     -    ${pkgs.hip}"
  ];

Blender

Hardware accelerated rendering can be achieved by using the package blender-hip.

OpenCL

hardware.opengl.extraPackages = with pkgs; [
  rocm-opencl-icd
  rocm-opencl-runtime
];

You should also install the clinfo package to verify that OpenCL is correctly setup (or check in the program you use to see if it is now available, such as in Darktable).

Vulkan

To enable vulkan

hardware.opengl.driSupport = true;
# For 32 bit applications
hardware.opengl.driSupport32Bit = true;


Note: amdvlk is not needed for vulkan

Starting from 20.09, the amdvlk drivers can be used in addition to the mesa radv drivers, the program will choose which one to use:

hardware.opengl.extraPackages = with pkgs; [
  amdvlk
];
# For 32 bit applications 
# Only available on unstable
hardware.opengl.extraPackages32 = with pkgs; [
  driversi686Linux.amdvlk
];

more information can be found here https://nixos.org/manual/nixos/unstable/index.html#sec-gpu-accel-vulkan

Problems

Dual Monitors

If you encounter problems having multiple monitors connected to your gpu, adding `video` parameters for each connector to the kernel command line sometimes helps.

For example:

boot.kernelParams = [
  "video=DP-1:2560x1440@144"
  "video=DP-2:2560x1440@144"
];

Of course you have to adjust the connector names (like `DP-1`), the resolution and frame rate accordingly.

To figure out your connector names, use:

head /sys/class/drm/*/status

with your monitors connected.