wpa_supplicant

General

wpa_supplicant can be enabled on NixOS with networking.wireless.enable = true.

Extra configuration can be specified inside networking.wireless.extraConfig.

wpa_supplicant_gui

To be able to use wpa_gui or wpa_cli as user put the following in your configuration.nix file:

networking.wireless.userControlled.enable = true;

Also your user must be part of the wheel group (replace USER with your username):

users.extraUsers.USER.extraGroups = [ "wheel" ];

Using wpa_supplicant from within the configuration file

You can configure your networks with the option networks. You have to fill the name(s) of your wifi(s) after the option and the preshared-key(s) (usually called psk). If you do not want to have your secret key in plaintext, you can use pskRaw, generated with wpa_passphrase SSID password. An example of using networks :

networking.wireless.networks.Wifi_name.pskRaw = "pskRaw generated";

If you have multiple networks, and you want to set the priority, you can use networking.wireless.networks.Wifi_name.priority = <value>;

A full example to connect to a university or similar network that uses MSCHAPV2 (like UWF):

  networking.wireless.networks."uwf-argo-air" = {
    hidden = true;
    auth = ''
      key_mgmt=WPA-EAP
      eap=PEAP
      phase2="auth=MSCHAPV2"
      identity="unx42"
      password="p@$$w0rd"
      '';
    };

To avoid having your network password in accessible plaintext on your system or in your version control consider using networking.wireless.environmentFile.

Switching Network

From the shell terminal, use the wpa_cli command line tool and specify the network interface device with -g

wpa_cli -g /run/wpa_supplicant/wlp3s0
list_network
select_network 2

As a means to debug if things are working, open another terminal and examine the logs by:

journalctl -u wpa_supplicant -f

MAC spoofing

Since there is no option to randomize your MAC address for wpa supplicant, you can instead create your own service using GNU's macchanger:

let
	change-mac = pkgs.writeShellScript "change-mac" ''
		card=$1
		tmp=$(mktemp)
		${pkgs.macchanger}/bin/macchanger "$card" -s | grep -oP "[a-zA-Z0-9]{2}:[a-zA-Z0-9]{2}:[^ ]*" > "$tmp"
		mac1=$(cat "$tmp" | head -n 1)
		mac2=$(cat "$tmp" | tail -n 1)
		if [ "$mac1" = "$mac2" ]; then
			if [ "$(cat /sys/class/net/"$card"/operstate)" = "up" ]; then
				${pkgs.iproute2}/bin/ip link set "$card" down &&
				${pkgs.macchanger}/bin/macchanger -r "$card"
				${pkgs.iproute2}/bin/ip link set "$card" up
			else
				${pkgs.macchanger}/bin/macchanger -r "$card"
			fi
		fi
	'';
in
	systemd.services.macchanger = {
		enable = true;
		description = "macchanger on wlan0";
		wants = [ "network-pre.target" ];
		before = [ "network-pre.target" ];
		bindsTo = [ "sys-subsystem-net-devices-wlan0.device" ];
		after = [ "sys-subsystem-net-devices-wlan0.device" ];
		wantedBy = [ "multi-user.target" ];
		serviceConfig = {
			Type = "oneshot";
			ExecStart = "${change-mac} wlan0";
		};
	};

Where you need to change the wlan0 with your own wifi network interface. You can list your interfaces by running ip link, your wifi network interface should have "wl" prepended. Note that the above snippet fully randomizes your MAC address, for more information you can read macchanger's manpage. This obviously requires you to have the macchanger package installed.

External links

(german) article eduroam meets NixOS (with configuration) (instance University of Applied Sciences Dresden: The eduroam installer for GNU/Linux works for example for Ubuntu but not NixOS)