NixOS on ARM/Installation: Difference between revisions
m Add further plans |
m removed mention of a specific nixos version in the command. |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 42: | Line 42: | ||
For <code>AArch64</code> it is possible to download images from Hydra. | For <code>AArch64</code> it is possible to download images from Hydra. | ||
* [https://hydra.nixos.org/job/nixos/release- | * [https://hydra.nixos.org/job/nixos/release-24.05/nixos.sd_image.aarch64-linux 24.05] | ||
* [https://hydra.nixos.org/job/nixos/trunk-combined/nixos.sd_image.aarch64-linux unstable (LTS kernel)] | * [https://hydra.nixos.org/job/nixos/trunk-combined/nixos.sd_image.aarch64-linux unstable (LTS kernel)] | ||
* [https://hydra.nixos.org/job/nixos/trunk-combined/nixos.sd_image_new_kernel_no_zfs.aarch64-linux unstable (Latest kernel)] | * [https://hydra.nixos.org/job/nixos/trunk-combined/nixos.sd_image_new_kernel_no_zfs.aarch64-linux unstable (Latest kernel)] | ||
On the page click on the latest successful build to get a download link under build products. | On the page click on the latest successful build to get a download link under build products. | ||
=== Installation steps === | === Installation steps === | ||
| Line 54: | Line 52: | ||
The .img files can be directly written to a microSD/SD card (minimal recommended size: 4 GB) using dd, once uncompressed from the ZSTD container. The SD card needs to be unmounted first. | The .img files can be directly written to a microSD/SD card (minimal recommended size: 4 GB) using dd, once uncompressed from the ZSTD container. The SD card needs to be unmounted first. | ||
Once the NixOS image file is downloaded, run the following command to install the image onto the SD Card, replace <code>/dev/mmcblk0</code> with the path to the SD card (use <code>dmesg</code> to find it out). | Once the NixOS image file is downloaded, run the following command to install the image onto the SD Card, replace <code>/dev/mmcblk0</code> with the path to the SD card (use <code>dmesg</code> to find it out) and image.img with the path to the image. | ||
<code> | <code> | ||
sudo dd if= | sudo dd if=image.img of=/dev/mmcblk0 | ||
</code> | </code> | ||
| Line 63: | Line 61: | ||
The base images are configured to boot up with a serial TTY ( RX/TX UART ) @ 115200 Baud. That way you not necessarily have to have a HDMI Display and keyboard. | The base images are configured to boot up with a serial TTY ( RX/TX UART ) @ 115200 Baud. That way you not necessarily have to have a HDMI Display and keyboard. | ||
Note: If the image has the extension <code>.zst</code>, it will need to be decompressed before writing to installation device. Use | |||
<code>nix-shell -p zstd --run "zstdcat image.img.zst | dd of=/dev/mmcblk0 status=progress"</code> | |||
to decompress the image on-the-fly. | |||
{{note| For some platforms, manually editing and adding kernel command-line arguments to <code>/boot/extlinux/extlinux.conf</code> may be needed for serial to work, and is "as" supported as would be editing the command-line manually during boot.}} | {{note| For some platforms, manually editing and adding kernel command-line arguments to <code>/boot/extlinux/extlinux.conf</code> may be needed for serial to work, and is "as" supported as would be editing the command-line manually during boot.}} | ||
Continue with [[NixOS_on_ARM/Initial_Configuration]]. | Continue with [[NixOS_on_ARM/Initial_Configuration]]. | ||
Latest revision as of 19:18, 1 August 2024
 |
This article or section is out of date.
Reason: This page needs a cleanup; it was migrated from an organically evolving article from about three wikis ago. The information may still be accurate though. (Discuss in Talk:NixOS on ARM/Installation)
Once the page has been updated this notice can be removed. |
Installation
Getting the installer
UEFI iso
Continue to the UEFI page.
SD card images (SBCs and similar platforms)
For AArch64 it is possible to download images from Hydra.
On the page click on the latest successful build to get a download link under build products.
Installation steps
The .img files can be directly written to a microSD/SD card (minimal recommended size: 4 GB) using dd, once uncompressed from the ZSTD container. The SD card needs to be unmounted first.
Once the NixOS image file is downloaded, run the following command to install the image onto the SD Card, replace /dev/mmcblk0 with the path to the SD card (use dmesg to find it out) and image.img with the path to the image.
sudo dd if=image.img of=/dev/mmcblk0
This should be enough to get you started, you may now boot your device for the first time.
The base images are configured to boot up with a serial TTY ( RX/TX UART ) @ 115200 Baud. That way you not necessarily have to have a HDMI Display and keyboard.
Note: If the image has the extension .zst, it will need to be decompressed before writing to installation device. Use
nix-shell -p zstd --run "zstdcat image.img.zst | dd of=/dev/mmcblk0 status=progress"
to decompress the image on-the-fly.
Continue with NixOS_on_ARM/Initial_Configuration.