NixOS on ARM

Installation images and miscellaneous boot files for ARM devices are built & hosted by @dezgeg at http://nixos-arm.dezgeg.me/installer.

A binary cache, containing a subset of the unstable channel, is hosted at http://nixos-arm.dezgeg.me/channel (signed with key nixos-arm.dezgeg.me-1:xBaUKS3n17BZPKeyxL4JfbTqECsT+ysbDJz29kLFRW0=%).

Additionally, thanks to Graham Christensen and Packet the official NixOS Hydra (https://cache.nixos.org) builds a full set of binaries for the AArch64 architecture on the nixpkgs-unstable channel.

Supported devices

The installation images should work on the following devices:

Manufacturer	Board	SoC	ISA	CPU	RAM	Storage
BeagleBoard.org	Beaglebone Black	TI AM335x	ARMv7	1x Cortex-A8 @ 1 GHz	512 MB	4 GB eMMC, microSD
NVIDIA	Jetson TK1	Tegra K1/T124	ARMv7	4x Cortex-A15 @ 2.3 GHz	2 GB	16 GB eMMC, SD, SATA
Linksprite	pcDuino3 Nano	Allwinner A20	ARMv7	2x Cortex-A7 @ 1 GHz	1 GB	4 GB NAND, microSD, SATA
Raspberry Pi Foundation	Raspberry Pi	Broadcom BCM2835	ARMv6	1x ARM1176 @ 700 MHz	256 MB / 512 MB	SD/microSD
Raspberry Pi Foundation	Raspberry Pi 2	Broadcom BCM2836	ARMv7	4x Cortex-A7 @ 900 MHz	1 GB	SD/microSD
Raspberry Pi Foundation	Raspberry Pi 3	Broadcom BCM2837	AArch64 / ARMv7	4x Cortex-A53 @ 1.2 GHz	1 GB	SD/microSD
Wandboard	Wandboard Solo/Dual/Quad	Freescale i.MX6	ARMv7	1x/2x/4x Cortex-A9 @ 1000 MHz	512 MB / 1 GB / 2 GB	microSD, SATA

QEMU emulation is not supported as of right now^Talk.

Installation

The installation images come in two flavors: sd-image-armv6l-linux.img is built for the ARMv6 architecture and it comes with the Raspberry Pi kernel. sd-image-armv7l-linux.img is built for the ARMv7 architecture and comes with the mainline multiplatform ARMv7 kernel (multi_v7_defconfig). Make sure you download the correct image for your board!

The .img files can be directly written to a microSD/SD card (minimal recommended size: 4 GB) using dd.

sudo dd if=sd-image-armv7l-linux.img of=/dev/sdX

Replace /dev/sdX with the path to your SD card device.

The base images are configured to boot up with a serial TTY ( RX/TX UART ) @ 115200 Baud. That way you not necessarily have to have a HDMI Display and keyboard.

Board-specific installation notes

Depending on the board, some additional preparation steps might be needed to make the SD card bootable on your device.

Beaglebone Black

U-Boot and its SPL (called the MLO) need to be copied to specific sectors on the microSD card with dd. Download U-Boot & MLO for the board (uboot-am335x_boneblack_defconfig-2017.03_u-boot.img, uboot-am335x_boneblack_defconfig-2017.03_MLO), and copy them to the correct location with (again, replace /dev/sdX with the correct path to the SD card device):

sudo dd if=uboot-am335x_boneblack_defconfig-2017.03_MLO        of=/dev/sdX count=1 seek=1 bs=128k
sudo dd if=uboot-am335x_boneblack_defconfig-2017.03_u-boot.img of=/dev/sdX count=2 seek=1 bs=384k

In case there is a valid boot loader on the eMMC of the board and the NixOS U-Boot isn't getting launched, try holding the button labeled 'S2' when resetting the board. Also the boot ROM might have a size limitation on the microSD cards used for booting; the author wasn't able to get a 64 GB SDXC card working but a 8 GB SDHC card worked.

Jetson TK1

The proprietary NVIDIA bootloader can only boot NVIDIA's L4T kernel, so it needs to be replaced by flashing U-Boot on the board's eMMC via the recovery USB port. The easiest way to do that is to use tegra-uboot-flasher-scripts, though unfortunately that's currently not packaged in NixOS. Once U-Boot is flashed, the ARMv7 image will boot out-of-the-box.

pcDuino 3 Nano

U-Boot needs to be copied to specific sectors on the microSD card with dd. Download U-Boot for the board (uboot-Linksprite_pcDuino3_Nano_defconfig-2015.07_u-boot-sunxi-with-spl.bin), and copy it to the correct location with (again, replace /dev/sdX with the correct path to the SD card device):

sudo dd if=uboot-Linksprite_pcDuino3_Nano_defconfig-2015.07_u-boot-sunxi-with-spl.bin of=/dev/sdX bs=1024 seek=8

Raspberry Pi (1)

The ARMv6 image boots out-of-the-box.

Raspberry Pi 2

The ARMv7 image should boot out-of-the-box, though the author hasn't personally tested this.

Raspberry Pi 3

Both the AArch64 and ARMv7 images boot out-of-the-box. Using the 64-bit AArch64 image is highly recommended, as the availability of binaries is much better and allows the use of the 64-bit instruction set.

Use the following GPIO Pins with an USB-TTL connector:

GND         - 3rd in top row, black cable
GPIO 14 TXD - 4th in top row, white cable
GPIO 15 RXD - 5th in top row, green cable

Use nix-shell -p screen --run "screen /dev/ttyUSB0 115200" to connect to the console. The image comes with wpa_supplicant, this to connect to your wifi:

$ wpa_passphrase  SSID > /etc/wpa_supplicant.conf
MYPASSWORD!<enter>
$ systemctl start wpa_supplicant

Wandboard

U-Boot and its SPL need to be copied to specific sectors on the microSD card with dd. Download U-Boot & SPL for the board (uboot-wandboard_defconfig-2017.03_u-boot.img, uboot-wandboard_defconfig-2017.03_SPL), and copy them to the correct location with (again, replace /dev/sdX with the correct path to the SD card device):

sudo dd if=uboot-wandboard_defconfig-2017.03_SPL        of=/dev/sdX seek=1 bs=1k
sudo dd if=uboot-wandboard_defconfig-2017.03_u-boot.img of=/dev/sdX seek=69 bs=1k

Only the Quad model has been tested, but the others should work as well with the same U-Boot binary.

NixOS installation & configuration

The installation image is actually a MBR partition table plus two partitions; a FAT32 /boot and a ext4 root filesystem. The image is designed such that it's possible to directly reuse the SD image's partition layout and "install" NixOS on the very same SD card by simply replacing the default configuration.nix and running nixos-rebuild. Using this installation method is strongly recommended, though if you know exactly what you're doing and how U-Boot on your board works, you can use nixos-install as usual. To help with the SD card installation method, the boot scripts on the image automatically resize the rootfs partition to fit the SD card on the first boot.

Use this as a template:

/etc/nixos/configuration.nix

{ config, pkgs, lib, ... }:
{
  # NixOS wants to enable GRUB by default
  boot.loader.grub.enable = false;
  # Enables the generation of /boot/extlinux/extlinux.conf
  boot.loader.generic-extlinux-compatible.enable = true;
 
  # !!! If your board is a Raspberry Pi 1, select this:
  boot.kernelPackages = pkgs.linuxPackages_rpi;
  # !!! Otherwise (even if you have a Raspberry Pi 2 or 3), pick this:
  boot.kernelPackages = pkgs.linuxPackages_latest;
  
  # !!! This is only for ARMv6 / ARMv7. Don't enable this on AArch64, cache.nixos.org works there.
  nix.binaryCaches = lib.mkForce [ "http://nixos-arm.dezgeg.me/channel" ];
  nix.binaryCachePublicKeys = [ "nixos-arm.dezgeg.me-1:xBaUKS3n17BZPKeyxL4JfbTqECsT+ysbDJz29kLFRW0=%" ];

  # !!! Needed for the virtual console to work on the RPi 3, as the default of 16M doesn't seem to be enough.
  boot.kernelParams = ["cma=32M"];
    
  # File systems configuration for using the installer's partition layout
  fileSystems = {
    "/boot" = {
      device = "/dev/disk/by-label/NIXOS_BOOT";
      fsType = "vfat";
    };
    "/" = {
      device = "/dev/disk/by-label/NIXOS_SD";
      fsType = "ext4";
    };
  };
    
  # !!! Adding a swap file is optional, but strongly recommended!
  # swapDevices = [ { device = "/swapfile"; size = 1024; } ];
}

Note: the default configuration.nix will contain something like imports = [ <nixos/modules/installer/cd-dvd/sd-image-armv7l-multiplatform.nix> ]; do not include that in your final installation or you will experience interesting problems. It is only for building the installation image!

To make the ARM experience slightly less painful, the config template adds nixos-arm.dezgeg.me as a binary cache, which contains a small subset of packages on the unstable channel (though a caution for US users: the server hosting them is physically located in Finland). Note that the binary cache isn't enabled on the prebuilt images, so enable it via the command line when building for the first time:

nixos-rebuild switch --fast --option binary-caches http://nixos-arm.dezgeg.me/channel --option binary-cache-public-keys nixos-arm.dezgeg.me-1:xBaUKS3n17BZPKeyxL4JfbTqECsT+ysbDJz29kLFRW0=%

Details about the boot process

On NixOS, all ARM boards use the popular U-Boot as the bootloader and U-Boot's Generic Distro Configuration Concept as the mechanism to communicate boot information (such as path to kernel zImage, initrd, DTB, command line arguments). For a quick TL;DR about the generic distro configuration support: U-Boot is scripted to scan all attached storage devices & partitions and look for a file named /extlinux/extlinux.conf or /boot/extlinux/extlinux.conf (which will be generated by NixOS, just like /boot/grub/grub.cfg is generated on PCs).

U-Boot also provides an interactive shell and the generation selection menu (just like GRUB). However, support for input or display devices varies greatly, depending on the board:

Beaglebone Black

Only serial console (via the 6-pin FTDI pin header) is supported.

Jetson TK1

Only serial console (via the DB-9 connector) is supported.

pcDuino 3 Nano

USB keyboards and HDMI displays work perfectly. Also a 3.3v serial port via the 3-pin header works.

Raspberry Pi (all versions)

USB keyboards and HDMI displays work perfectly. Using the 3.3v serial port via the pin headers (exact location depends on hardware version) should also work.

Wandboard

Only serial console (via the DB-9 connector) is supported.

Porting NixOS to new boards

The easy way

(if you're lucky)

If your board is an ARMv7 board supported by multi_v7_defconfig and you have access to U-Boot on the board, getting sd-image-armv7l-linux.img to boot is the easiest option:

• If you're lucky and your U-Boot build comes with the extlinux.conf support built in, the image boots out-of-the-box. This is the case for all (upstream) Allwinner and Tegra U-Boots, for instance.
• Otherwise, you can get the boot information (path to kernel zImage, initrd, DTB, command line arguments) by extracting extlinux.conf from the boot partition of the image, and then attempt to boot it via the U-Boot shell, or some other mechanism that your board's distro uses (e.g. uEnv.txt).

Building u-boot from your NixOS PC

Assuming

• Your board is supported upstream by u-boot or there is a recent enough fork with extlinux.conf support.
• You do not have nix setup on an ARM device
• Your nix isn't setup for cross-compilation

It is still possible to build u-boot using tools provided by NixOS.

In the following terminal session, replace orangepi_pc_defconfig with the appropriate board from the configs folder of u-boot.

$ nix-shell -E 'with import <nixpkgs> {}; stdenv.mkDerivation { name = "arm-shell"; buildInputs = [git gnumake gcc gcc-arm-embedded dtc]; }'
$ git clone git://git.denx.de/u-boot.git
$ cd u-boot
# We're checking out a version from before the use of `binman`.
# The dtc package is 1.4.2, which does not include `pylibftd`.
# Furthermore, I do not know how to package the library so it would be
# available in the python interpreter, making binman happy.
$ git checkout v2017.03
$ make -j4 ARCH=arm CROSS_COMPILE=arm-none-eabi- orangepi_pc_defconfig
$ make -j4 ARCH=arm CROSS_COMPILE=arm-none-eabi-

The name of the final file will change depending on the board. For this specific build, and most Allwinner builds, the file will be named u-boot-sunxi-with-spl.bin.

The hard way

Alternatively/if all else fails, you can do it the hard way and bootstrap NixOS from an existing ARM Linux installation.

Contributing new boards to nixpkgs

• Add a new derivation for your board's U-Boot configuration, see for example ubootJetsonTK1 in all-packages.nix.
• If your board's U-Boot configuration doesn't use the extlinux.conf format by default, create a patch to enable it. Some C hacking skills & U-Boot knowledge might be required. For some pointers, see this patch to enable it on the Versatile Express.
• Make a pull request, also containing the board-specific instructions. Ping @dezgeg for review and for building & hosting the U-Boots at http://nixos-arm.dezgeg.me/installer.