Btrfs: Difference between revisions

From NixOS Wiki
imported>Onny
Note on set snapshot read-write again
imported>Onny
Add note on removing a subvolume
Line 92: Line 92:
<syntaxhighlight lang="bash">
<syntaxhighlight lang="bash">
btrfs subvolume create /mnt/nixos
btrfs subvolume create /mnt/nixos
</syntaxhighlight>
Removing a subvolume
<syntaxhighlight lang="bash">
btrfs subvolume delete /mnt/nixos
</syntaxhighlight>
</syntaxhighlight>



Revision as of 19:56, 10 February 2023

btrfs is a modern copy on write (CoW) filesystem for Linux aimed at implementing advanced features while also focusing on fault tolerance, repair and easy administration.

Installation

Note: The following example is for EFI enabled systems. Adjust commands accordingly for a BIOS installation.

Partition the disk

# printf "label: gpt\n,550M,U\n,,L\n" | sfdisk /dev/sdX

Format partitions and create subvolumes

# mkfs.fat -F 32 /dev/sdX1

# mkfs.btrfs /dev/sdX2
# mkdir -p /mnt
# mount /dev/sdX2 /mnt
# btrfs subvolume create /mnt/root
# btrfs subvolume create /mnt/home
# btrfs subvolume create /mnt/nix
# umount /mnt

Mount the partitions and subvolumes

# mount -o compress=zstd,subvol=root /dev/sdX2 /mnt
# mkdir /mnt/{home,nix}
# mount -o compress=zstd,subvol=home /dev/sdX2 /mnt/home
# mount -o compress=zstd,noatime,subvol=nix /dev/sdX2 /mnt/nix

# mkdir /mnt/boot
# mount /dev/sdX1 /mnt/boot

Install NixOS

# nixos-generate-config --root /mnt
# nano /mnt/etc/nixos/configuration.nix # manually add mount options
# nixos-install

Configuration

Compression

nixos-generate-config --show-hardware-config doesn't detect mount options automatically, so to enable compression, you must specify it and other mount options in a persistent configuration:

fileSystems = {
  "/".options = [ "compress=zstd" ];
  "/home".options = [ "compress=zstd" ];
  "/nix".options = [ "compress=zstd" "noatime" ];
  "/swap".options = [ "noatime" ];
};

Swap file

Optionally, create a separate subvolume for the swap file. Be sure to regenerate your hardware-configuration.nix if you choose to do this.

# mkdir -p /mnt
# mount /dev/sdXY /mnt
# btrfs subvolume create /mnt/swap
# umount /mnt
# mkdir /swap
# mount -o subvol=swap /dev/sdXY /swap

Then, create the swap file with copy-on-write and compression disabled:

# truncate -s 0 /swap/swapfile
# chattr +C /swap/swapfile
# btrfs property set /swap/swapfile compression none
# dd if=/dev/zero of=/swap/swapfile bs=1M count=4096
# chmod 0600 /swap/swapfile
# mkswap /swap/swapfile

Finally, add the swap file to your configuration and nixos-rebuild switch:

swapDevices = [ { device = "/swap/swapfile"; } ];

Usage

Subvolume

Create a subvolume

btrfs subvolume create /mnt/nixos

Removing a subvolume

btrfs subvolume delete /mnt/nixos

Snapshots

Taking a read-only (-r) snapshot called nixos_snapshot_202302 of the subvolume mounted at /

btrfs subvolume snapshot -r / /mnt/@nixos_snapshot_202302

Make snapshot read-write again

btrfs property set -ts /mnt/@nixos_snapshot_202302 ro false

List snapshots for /

sudo btrfs subvolume list /

Transfer snapshot

Sending the snapshot /mnt/@nixos_snapshot_202302 compressed to a remote host via ssh at root@192.168.178.110 and saving it to a subvolume mounted or directory at /mnt/nixos

sudo btrfs send /mnt/@nixos_snapshot_202302 | zstd | ssh root@192.168.178.110 'zstd -d | btrfs receive /mnt/nixos'