NixOS on ARM

From NixOS Wiki
Revision as of 08:36, 11 September 2017 by imported>Dezgeg (Update Raspi-related things)

Installation images and miscellaneous boot files for ARM devices are built & hosted by @dezgeg at http://nixos-arm.dezgeg.me/installer.

A binary cache, containing a subset of the unstable channel, is hosted at http://nixos-arm.dezgeg.me/channel (signed with key nixos-arm.dezgeg.me-1:xBaUKS3n17BZPKeyxL4JfbTqECsT+ysbDJz29kLFRW0=%).

Supported devices

The installation images have been tested on the following devices:

Manufacturer Board SoC ISA CPU RAM Storage
NVIDIA Jetson TK1 Tegra K1/T124 ARMv7 4x Cortex-A15 @ 2.3 GHz 2 GB 16 GB eMMC, SD, SATA
Linksprite pcDuino3 Nano Allwinner A20 ARMv7 2x Cortex-A7 @ 1 GHz 1 GB 4 GB NAND, microSD, SATA
Raspberry Pi Foundation Raspberry Pi BCM2835 ARMv6 1x ARM1176 @ 700 MHz 256/512 MB SD/microSD
Raspberry Pi Foundation Raspberry Pi 2 BCM2836 ARMv7 4x Cortex-A7 @ 900 MHz 256/512 MB SD/microSD

QEMU emulation is not supported as of right nowTalk.

Installation

The installation images come in two flavors: sd-image-armv6l-linux.img is built for the ARMv6 architecture and it comes with the Raspberry Pi kernel. sd-image-armv7l-linux.img is built for the ARMv7 architecture and comes with the mainline multiplatform ARMv7 kernel (multi_v7_defconfig). Make sure you download the correct image for your board!

The .img files can be directly written to a microSD/SD card (minimal recommended size: 4 GB) using dd. For example, if your SD card shows up as /dev/sdc:

sudo dd if=sd-image-armv7l-linux.img of=/dev/sdc

(As always, be careful when using dd so you don't wipe your hard drive!)

Board-specific installation notes

Depending on the board, some additional preparation steps might be needed to make the SD card bootable on your device.

Jetson TK1

The proprietary NVIDIA bootloader can only boot NVIDIA's L4T kernel, so it needs to be replaced by flashing U-Boot on the board's eMMC via the recovery USB port. The easiest way to do that is to use tegra-uboot-flasher-scripts, though unfortunately that's currently not packaged in NixOS. Once U-Boot is flashed, the ARMv7 image will boot out-of-the-box.

pcDuino 3 Nano

U-Boot needs to be copied to the microSD card with dd, with parameters bs=1024 seek=8. Download U-Boot for the board (uboot-Linksprite_pcDuino3_Nano_defconfig-2015.07_u-boot-sunxi-with-spl.bin), and copy it to the correct location with (assuming the SD card still shows up as /dev/sdc):

sudo dd if=uboot-Linksprite_pcDuino3_Nano_defconfig-2015.07_u-boot-sunxi-with-spl.bin of=/dev/sdc bs=1024 seek=8

Raspberry Pi (1)

The ARMv6 image boots out-of-the-box.

Raspberry Pi 2

The ARMv7 image should boot out-of-the-box, though the author hasn't personally tested this.

NixOS installation & configuration

The installation image is actually a MBR partition table plus two partitions; a FAT32 /boot and a ext4 root filesystem. The image is designed such that it's possible to directly reuse the SD image's partition layout and "install" NixOS on the very same SD card by simply replacing the default configuration.nix and running nixos-rebuild. Using this installation method is strongly recommended, though if you know exactly what you're doing and how U-Boot on your board works, you can use nixos-install as usual. To help with the SD card installation method, the boot scripts on the image automatically resize the rootfs partition to fit the SD card on the first boot.

Use this as a template:

{ config, pkgs, lib, ... }:
{
  # NixOS wants to enable GRUB by default
  boot.loader.grub.enable = false;
  # Enables the generation of /boot/extlinux/extlinux.conf
  boot.loader.generic-extlinux-compatible.enable = true;
 
  # !!! If your board is a Raspberry Pi, select this:
  boot.kernelPackages = pkgs.linuxPackages_rpi;
  # !!! Otherwise, pick this:
  boot.kernelPackages = pkgs.linuxPackages_latest;
  
  nix.binaryCaches = lib.mkForce [ "http://nixos-arm.dezgeg.me/channel" ];
  nix.binaryCachePublicKeys = [ "nixos-arm.dezgeg.me-1:xBaUKS3n17BZPKeyxL4JfbTqECsT+ysbDJz29kLFRW0=%" ];
    
  # File systems configuration for using the installer's partition layout
  fileSystems = {
    "/boot" = {
      device = "/dev/disk/by-label/NIXOS_BOOT";
      fsType = "vfat";
    };
    "/" = {
      device = "/dev/disk/by-label/NIXOS_SD";
      fsType = "ext4";
    };
  };
    
  # !!! Adding a swap file is optional, but strongly recommended!
  # swapDevices = [ { device = "/swapfile"; size = 1024; } ];
}

Note: the default configuration.nix will contain something like imports = [ <nixos/modules/installer/cd-dvd/sd-image-armv7l-multiplatform.nix> ]; do not include that in your final installation or you will experience interesting problems. It is only for building the installation image!

To make the ARM experience slightly less painful, the config template adds nixos-arm.dezgeg.me as a binary cache, which contains a small subset of packages on the unstable channel (though a caution for US users: the server hosting them is physically located in Finland). Note that the binary cache isn't enabled on the prebuilt images, so enable it via the command line when building for the first time:

nixos-rebuild switch --fast --option binary-caches http://nixos-arm.dezgeg.me/channel --option binary-cache-public-keys nixos-arm.dezgeg.me-1:xBaUKS3n17BZPKeyxL4JfbTqECsT+ysbDJz29kLFRW0=%

Details about the boot process

On NixOS, all ARM boards use the popular U-Boot as the bootloader and U-Boot's Generic Distro Configuration Concept as the mechanism to communicate boot information (such as path to kernel zImage, initrd, DTB, command line arguments). For a quick TL;DR about the generic distro configuration support: U-Boot is scripted to scan all attached storage devices & partitions and look for a file named /extlinux/extlinux.conf or /boot/extlinux/extlinux.conf (which will be generated by NixOS, just like /boot/grub/grub.cfg is generated on PCs).

U-Boot also provides an interactive shell and the generation selection menu (just like GRUB). However, support for input or display devices varies greatly, depending on the board:

Jetson TK1

Only serial console (via the DB-9 connector) is supported.

pcDuino 3 Nano

USB keyboards and HDMI displays work perfectly. Also a 3.3v serial port via the 3-pin header works.

Raspberry Pi (all versions)

USB keyboards and HDMI displays work perfectly.

Using the 3.3v serial port via the pin headers (exact location depends on hardware version) should also work.

Porting NixOS to new boards

The easy way (if you're lucky)

If your board is an ARMv7 board supported by multi_v7_defconfig and you have access to U-Boot on the board, getting sd-image-armv7l-linux.img to boot is the easiest option:

  • If you're lucky and your U-Boot build comes with the extlinux.conf support built in, the image boots out-of-the-box. This is the case for all (upstream) Allwinner and Tegra U-Boots, for instance.
  • Otherwise, you can get the boot information (path to kernel zImage, initrd, DTB, command line arguments) by extracting extlinux.conf from the boot partition of the image, and then attempt to boot it via the U-Boot shell, or some other mechanism that your board's distro uses (e.g. uEnv.txt).

The hard way

Alternatively/if all else fails, you can do it the hard way and bootstrap NixOS from an existing ARM Linux installation.

Contributing new boards to nixpkgs

  • Add a new derivation for your board's U-Boot configuration, see for example ubootJetsonTK1 in all-packages.nix.
  • If your board's U-Boot configuration doesn't use the extlinux.conf format by default, create a patch to enable it. Some C hacking skills & U-Boot knowledge might be required. For some pointers, see this patch to enable it on the Versatile Express.
  • Make a pull request, also containing the board-specific instructions. Ping @dezgeg for review and for building & hosting the U-Boots at http://nixos-arm.dezgeg.me/installer.