NixOS on RISCV/VisionFive 2

← Back to RISC-V

VisionFive 2
Manufacturer	StarFive
Architecture	RISC-V
Bootloader	Custom or UEFI
Boot order	Configurable; SD, USB, Netboot
Maintainer	onny
VisionFive 2
SoC	JH7110

The VisionFive 2 is a single board computer (SBC) that uses a RISC-V processor with an integrated GPU. It supports Linux operating system and various multimedia features, such as 4K video decoding and OpenGL ES 3.212.

Status

The Visionfive 2 developers have pushed their Linux kernel patches quite early to the upstream mainline kernel and have gotten almost all merged already.

See https://rvspace.org/en/project/JH7110_Upstream_Plan for an overview of what device is supported in which Linux kernel version.

NixOS (more precisely nixpkgs) already has the generic Linux kernel 6.9 available, which supports almost everything you need out of the box (for a server as HDMI display patches haven't been merged into 6.9). This means NixOS should be able to run without a custom kernel.

Building a SD-card image

This example assumes you have the latest revision of the board (v1.3) with 8GB memory. For other configurations please consult the nixos-hardware documentation on this board. First create this Flake file

flake.nix

{
  inputs.nixpkgs.url = "github:nixos/nixpkgs/nixos-23.11";
  inputs.nixos-hardware.url = "github:nixos/nixos-hardware";

  # Some dependencies of this flake are not yet available on non linux systems
  inputs.systems.url = "github:nix-systems/x86_64-linux";
  inputs.flake-utils.url = "github:numtide/flake-utils";
  inputs.flake-utils.inputs.systems.follows = "systems";

  outputs = { self, nixpkgs, nixos-hardware, flake-utils, ... }:
    flake-utils.lib.eachDefaultSystem (system:
      rec {
        packages.default = packages.sd-image;
        packages.sd-image = (import "${nixpkgs}/nixos" {
          configuration =
            { config, ... }: {
              imports = [
                "${nixos-hardware}/starfive/visionfive/v2/sd-image-installer.nix"
              ];

              # If you want to use ssh set a password
              users.users.nixos.password = "test123";
              # OR add your public ssh key
              # users.users.nixos.openssh.authorizedKeys.keys = [ "ssh-rsa ..." ];

              # AND configure networking
              networking.interfaces.end0.useDHCP = true;
              networking.interfaces.end1.useDHCP = true;

              # Additional configuration goes here

              hardware.deviceTree.overlays = [{
                name = "8GB-patch";
                dtsFile = "${nixos-hardware}/starfive/visionfive/v2/8gb-patch.dts";
              }];

              sdImage.compressImage = false;

              nixpkgs.crossSystem = {
                config = "riscv64-unknown-linux-gnu";
                system = "riscv64-linux";
              };

              system.stateVersion = "23.11";
            };
          inherit system;
        }).config.system.build.sdImage;
      });
}

Run following command to build the SD-card image

nix build .#

After successfull build, flash the resulting file in the directory results/sd-image to the target device, in this example the SD-card (/dev/mmcblk*). Note that everything on the target device gets erased.

dd if=result/sd-image/nixos-sd-image-23.11pre-git-riscv64-linux-starfive-visionfive2.img of=/dev/mmcblk0 status=progress

Usage

First enable booting from SD-card by enabling jumper 1 and 2

Move jumpers to the right away from the numbers to enable SD-card booting

For UART access, wire GND (black), RX (blue) and TX (purple) to your adapter

Update board firmware

sudo visionfive2-firmware-update-flash

Bootstrap NixOS system configuration at /etc/nixos/configuration.nix

nixos-generate-config