U-Boot

U-Boot is a common platform firmware implementation for embedded and embedded-like devices.

It may also be used as a bootloader, but with modern U-Boot, UEFI boot is generally possible too.

U-Boot in Nixpkgs

Mainline U-Boot is packaged in Nixpkgs.

⤟︎

This template is a candidate for merging with Template:Nixpkg. They seem to be duplicates. Further information may be found in the relevant discussion page.

pkgs/misc/uboot/default.nix

Vendor forks of U-Boot are generally not packaged in Nixpkgs, and generally unwelcome.

U-Boot may be patched for compatibility reasons mainly, and work should be taken to send them to mainline U-Boot.

Building a packaged U-Boot

You need to know two things:

1. The target ISA (Instruction Set Architecture)
2. If you need to cross-compile

The target ISA is the ISA of the target board. This would be defined by the CPU used on the board.

You will need to cross-compile if you are not building on the same architecture as the target board. For example, if you are building for an AArch64 target board on a standard x86_64 laptop, you would need to cross-compile.

With those facts known, you can build the appropriate attribute from a Nixpkgs checkout.

The general format is:

$ nix-build -A [pkgsCross.$cross_name.]$packageName
$ # Where the part in [brackets] is needed for cross-compilation.

pkgsCross attribute name cheat sheet

Architecture	Package Set
aarch64	aarch64-multiplatform
armv7l	armv7l-hf-multiplatform
armv6l	raspberryPi [sic]

Example build

The following examples use the U-Boot package for a LibreTech CC ‘LePotato’, which uses an S905X SoC. This SoC uses an AArch64 ISA.

To build the package with cross-compilation, you need to prefix with the correct cross-compilation package set:

$ # Example running on x86_64.
$ uname -m 
x86_64
$ nix-build -A pkgsCross.aarch64-multiplatform.ubootLibreTechCC

If, instead, you are building natively (same architecture) you can refer to the package attribute name directly:

$ # Example output for an AArch64 system.
$ uname -m 
aarch64
$ nix-build -A ubootLibreTechCC

Installing U-Boot

You will need to consult either the Official U-Boot documentation, or a board-specific page to find out how to use the produced output.

The large variety of ecosystems supported by U-Boot makes it impossible to document succinctly.

SBC and related projects in NixOS

• NixOS on ARM
• NixOS on RISCV

Using NixOS with U-Boot

Note: This section assumes U-Boot is installed already.

With U-Boot, NixOS currently still assumes use of U-Boot's Generic Distro Configuration Concept as the mechanism for discoverable boot. The preferred scheme is extlinux-compatible. This is how the kernel Image, initrd, dtb, and Kernel command-line arguments are provided with complete support for the lifecycles of generations.

Note that U-Boot is moving to U-Boot Standard Boot. How it affects the assumptions from NixOS is still not documented.

Booting through UEFI with U-Boot should work. Booting with UEFI is tentatively supported, with intent of being the only fully supported boot method in the future. See NixOS on ARM/UEFI, which describes part of the drawbacks.

Quick overview about the Generic Distro Configuration support

U-Boot is scripted to scan all attached storage devices and partitions, and look for a file named /extlinux/extlinux.conf or /boot/extlinux/extlinux.conf. This will will be generated by NixOS when configured with boot.loader.generic-extlinux-compatible.enable.

The partition also needs to have its "bootable" flag set. This is true for both MBR and GPT partitioning schemes.

Vendor U-Boot

The term vendor U-Boot means the provided pre-built U-Boot binaries and the source as well. It generally implies use of an older fork of U-Boot from a BSP (Board Support Package).

Vendor U-Boot may or may not work to boot and use NixOS.

The answer is actually really complicated, and depends not only about U-Boot, but the intended Linux kernel to be booted, and the boot method in use.

The buildUBoot implementation in Nixpkgs may or may not work to build a vendor U-Boot, and this usage is unsupported.

A few vendors ship good pre-built modern U-Boot implementations. Booting NixOS with those should work. If it does not, things may need to be fixed on any of the end. But also, this depends on the kernel, and boot method in use.

Other U-Boot distributions

There exists other pre-built U-Boot distributions. As long as they follow the mainline U-Boot semantics, and are close enough in age to the current releases, they should work to boot NixOS.

Tow-Boot

Sidenote: Tow-Boot is not a NixOS project.
Though it is built with Nix expressions, and made by authors involved with the NixOS project.

Stock NixOS should be assumed to work with Tow-Boot, always depending on the boot method and kernel in use.

Tow-Boot is currently used as a reference as the only distro-agnostic U-Boot build, for support purposes.

See also

• NixOS on ARM/UEFI
• Official U-Boot source repo
• Official U-Boot documentation