Setting up WireGuard

Generate keypair

Each peer needs to have a public-private keypair. The keys can be generated on any machine that already has WireGuard installed using the wg utility. If WireGuard isn't installed yet, it can be made available by adding wireguard to environment.systemPackages or by running nix-env -iA wireguard.

Creating a keypair is simple:

umask 077
mkdir ~/wireguard-keys
wg genkey > ~/wireguard-keys/private
wg pubkey < ~/wireguard-keys/private > ~/wireguard-keys/public

You can create as many keypairs as you like for different connections or roles; it is also possible to reuse the same keypair for every connection.

Server setup

Enable WireGuard on the server via /etc/nixos/configuration.nix:

{
  ...

  # enable NAT
  networking.nat.enable = true;
  networking.nat.externalInterface = "eth0";
  networking.nat.internalInterfaces = [ "wg0" ];
  networking.firewall = {
    allowedUDPPorts = [ 51820 ];
  };

  networking.wireguard.interfaces = {
    # "wg0" is the network interface name. You can name the interface arbitrarily.
    wg0 = {
      # Determines the IP address and subnet of the server's end of the tunnel interface.
      ips = [ "10.100.0.1/24" ];

      # The port that WireGuard listens to. Must be accessible by the client.
      listenPort = 51820;

      # This allows the wireguard server to route your traffic to the internet and hence be like a VPN
      # For this to work you have to set the dnsserver IP of your router (or dnsserver of choice) in your clients
      postSetup = ''
        ${pkgs.iptables}/bin/iptables -t nat -A POSTROUTING -s 10.100.0.0/24 -o eth0 -j MASQUERADE
      '';

      # This undoes the above command
      postShutdown = ''
        ${pkgs.iptables}/bin/iptables -t nat -D POSTROUTING -s 10.100.0.0/24 -o eth0 -j MASQUERADE
      '';

      # Path to the private key file.
      #
      # Note: The private key can also be included inline via the privateKey option,
      # but this makes the private key world-readable; thus, using privateKeyFile is
      # recommended.
      privateKeyFile = "path to private key file";

      peers = [
        # List of allowed peers.
        { # Feel free to give a meaning full name
          # Public key of the peer (not a file path).
          publicKey = "{client public key}";
          # List of IPs assigned to this peer within the tunnel subnet. Used to configure routing.
          allowedIPs = [ "10.100.0.2/32" ];
        }
        { # John Doe
          publicKey = "{john doe's public key}";
          allowedIPs = [ "10.100.0.3/32" ];
        }
      ];
    };
  };
  ...
}

Client setup

{
  ...
  networking.firewall = {
    allowedUDPPorts = [ 51820 ]; # Clients and peers can use the same port, see listenport
  };
  # Enable WireGuard
  networking.wireguard.interfaces = {
    # "wg0" is the network interface name. You can name the interface arbitrarily.
    wg0 = {
      # Determines the IP address and subnet of the client's end of the tunnel interface.
      ips = [ "10.100.0.2/24" ];
      listenPort = 51820; # to match firewall allowedUDPPorts (without this wg uses random port numbers)

      # Path to the private key file.
      #
      # Note: The private key can also be included inline via the privateKey option,
      # but this makes the private key world-readable; thus, using privateKeyFile is
      # recommended.
      privateKeyFile = "path to private key file";

      peers = [
        # For a client configuration, one peer entry for the server will suffice.

        {
          # Public key of the server (not a file path).
          publicKey = "{server public key}";

          # Forward all the traffic via VPN.
          allowedIPs = [ "0.0.0.0/0" ];
          # Or forward only particular subnets
          #allowedIPs = [ "10.100.0.1" "91.108.12.0/22" ];

          # Set this to the server IP and port.
          endpoint = "{server ip}:51820"; # ToDo: route to endpoint not automatically configured https://wiki.archlinux.org/index.php/WireGuard#Loop_routing https://discourse.nixos.org/t/solved-minimal-firewall-setup-for-wireguard-client/7577

          # Send keepalives every 25 seconds. Important to keep NAT tables alive.
          persistentKeepalive = 25;
        }
      ];
    };
  };
  ...
}

Multiple connections can be configured by configuring multiple interfaces under networking.wireguard.interfaces.

Setting up WireGuard server/client with wg-quick and dnsmasq

Server setup

DNS requires opening TCP/UDP port 53.

{
  ...
  # Enable NAT
  networking.nat = {
    enable = true;
    externalInterface = "eth0";
    internalInterfaces = [ "wg0" ];
  };
  # Open ports in the firewall
  networking.firewall = {
    allowedTCPPorts = [ 53 ];
    allowedUDPPorts = [ 53 51820 ];
  };
  ...
}

The wg-quick setup is similar to the previous setup.

{
  ...
  networking.wg-quick.interfaces = {
    # "wg0" is the network interface name. You can name the interface arbitrarily.
    wg0 = {
      # Determines the IP/IPv6 address and subnet of the client's end of the tunnel interface
      address = [ "10.0.0.1/24" "fdc9:281f:04d7:9ee9::1/64" ];
      # The port that WireGuard listens to - recommended that this be changed from default
      listenPort = 51820;
      # Path to the server's private key
      privateKeyFile = "/root/wireguard-keys/privatekey";

      # This allows the wireguard server to route your traffic to the internet and hence be like a VPN
      postUp = ''
        ${pkgs.iptables}/bin/iptables -A FORWARD -i wg0 -j ACCEPT
        ${pkgs.iptables}/bin/iptables -t nat -A POSTROUTING -s 10.0.0.1/24 -o eth0 -j MASQUERADE
        ${pkgs.iptables}/bin/ip6tables -A FORWARD -i wg0 -j ACCEPT
        ${pkgs.iptables}/bin/ip6tables -t nat -A POSTROUTING -s fdc9:281f:04d7:9ee9::1/64 -o eth0 -j MASQUERADE
      '';

      # Undo the above
      preDown = ''
        ${pkgs.iptables}/bin/iptables -D FORWARD -i wg0 -j ACCEPT
        ${pkgs.iptables}/bin/iptables -t nat -D POSTROUTING -s 10.0.0.1/24 -o eth0 -j MASQUERADE
        ${pkgs.iptables}/bin/ip6tables -D FORWARD -i wg0 -j ACCEPT
        ${pkgs.iptables}/bin/ip6tables -t nat -D POSTROUTING -s fdc9:281f:04d7:9ee9::1/64 -o eth0 -j MASQUERADE
      '';

      peers = [
        { # peer0
          publicKey = "{client public key}";
          presharedKeyFile = "/root/wireguard-keys/preshared_from_peer0_key";
          allowedIPs = [ "10.0.0.2/32" "fdc9:281f:04d7:9ee9::2/128" ];
        }
        # More peers can be added here.
      ];
    };
  };
  ...
}

To enable dnsmasq and only serve DNS requests to the WireGuard interface add the following:

{
  ...
  services = {
    ...
    dnsmasq = {
      enable = true;
      extraConfig = ''
        interface=wg0
      '';
    };
    ...
  };
  ...
}

Client setup

The client will now point DNS to the server.

{
  ...
  networking.wg-quick.interfaces = {
    wg0 = {
      address = [ "10.0.0.2/24" "fdc9:281f:04d7:9ee9::2/64" ];
      dns = [ "10.0.0.1" "fdc9:281f:04d7:9ee9::1" ];
      privateKeyFile = "/root/wireguard-keys/privatekey";
      
      peers = [
        {
          publicKey = "{server public key}";
          presharedKeyFile = "/root/wireguard-keys/preshared_from_peer0_key";
          allowedIPs = [ "0.0.0.0/0" "::/0" ];
          endpoint = "{server ip}:51820";
          persistentKeepalive = 25;
        }
      ];
    };
  };
  ...
}

Setting up WireGuard with systemd-networkd

Please note, that networkd support in NixOS is still experimental.

Client setup

{ config, pkgs, lib, ... }:{
  boot.extraModulePackages = [ config.boot.kernelPackages.wireguard ];
  systemd.network = {
    enable = true;
    netdevs = {
      "10-wg0" = {
        netdevConfig = {
          Kind = "wireguard";
          MTUBytes = "1300";
          Name = "wg0";
        };
        # See also man systemd.netdev
        extraConfig = ''
          [WireGuard]
          # Currently, the private key must be world readable, as the resulting netdev file will reside in the Nix store.
          PrivateKey=EMlybyTmXI/4z311xU9S3m82mC2OOMRfRM0Okiik83o=
          ListenPort=9918

          [WireGuardPeer]
          PublicKey=OhApdFoOYnKesRVpnYRqwk3pdM247j8PPVH5K7aIKX0=
          AllowedIPs=fc00::1/64, 10.100.0.1
          Endpoint={set this to the server ip}:51820
        '';
      };
    };
    networks = {
      # See also man systemd.network
      "40-wg0".extraConfig = ''
        [Match]
        Name=wg0

        [Network]
        DHCP=none
        IPv6AcceptRA=false
        Gateway=fc00::1
        Gateway=10.100.0.1
        DNS=fc00::53
        NTP=fc00::123

        # IP addresses the client interface will have
        [Address]
        Address=fe80::3/64
        [Address]
        Address=fc00::3/120
        [Address]
        Address=10.100.0.2/24
      '';
    };
  };
};

Setting up WireGuard with NetworkManager

This is probably only useful on clients. Functionality is present in NetworkManager since version 1.20 but network-manager-applet can show and control wireguard connections since version 1.22 only (available since NixOS 21.05).

If you intend to route all your traffic through the wireguard tunnel, the default configuration of the NixOS firewall will block the traffic because of rpfilter. You can either disable rpfilter altogether:

{ config, pkgs, lib, ... }:{
  networking.firewall.checkReversePath = false; # maybe "loose" also works, untested
}

or you can adapt the rpfilter to ignore wireguard related traffic (replace 51820 by the port of your wireguard endpoint):

{ config, pkgs, lib, ... }:{
  networking.firewall = {
   # if packets are still dropped, they will show up in dmesg
   logReversePathDrops = true;
   # wireguard trips rpfilter up
   extraCommands = ''
     ip46tables -t raw -I nixos-fw-rpfilter -p udp -m udp --sport 51820 -j RETURN
     ip46tables -t raw -I nixos-fw-rpfilter -p udp -m udp --dport 51820 -j RETURN
   '';
   extraStopCommands = ''
     ip46tables -t raw -D nixos-fw-rpfilter -p udp -m udp --sport 51820 -j RETURN || true
     ip46tables -t raw -D nixos-fw-rpfilter -p udp -m udp --dport 51820 -j RETURN || true
   '';
  };
}

Adding a wireguard connection to NetworkManager is not straightforward to do fully in gui, it is simpler to reuse a configuration file for wg-guick. For example:

[Interface]
# your own IP on the wireguard network
Address = 10.0.0.3/24, fd4:8e3:226:2e0::3/64
Table = auto
PrivateKey = 0000000000000000000000000000000000000000000=

[Peer]
PublicKey = 1111111111111111111111111111111111111111111=
# restrict this to the wireguard subnet if you don't want to route everything to the tunnel
AllowedIPs = 0.0.0.0/0, ::/0
# ip and port of the peer
Endpoint = 1.2.3.4:51820

Then run

nmcli connection import type wireguard file thefile.conf

The new VPN connection should be available, you still have to click on it to activate it.