NixOS Installation Guide

This guide is a companion guide for the official manual. In addition to describing the steps from the official manual, it provides known good instructions for common use cases. When there is a discrepancy between the manual and this guide, the supported case is the one described in the manual.

Use this guide as a step-by-step guide, choices will be presented, use only the selected section, and continue at the section it tells you to at the end.

Installation target

NixOS can be installed on an increasing variety of hardware:

• regular (Intel or AMD) desktop computers, laptops or physically accessible servers, covered on this page
• SBCs (like the Raspberry Pis) and other ARM boards, see NixOS on ARM
• cloud and remote servers, see NixOS friendly hosters

Installation method

NixOS, as with most Linux-based operating systems, can be installed in different ways.

1. The classic way, booting from the installation media. (Described below.)
2. Booting the media from an existing Linux installation

Making the installation media

Since NixOS 14.11 the installer ISO is hybrid. This means it is bootable on both CD and USB drives. It also boots on EFI systems, like most modern motherboards and apple systems. The following instructions will assume the standard way of copying the image to a USB drive. When using a CD or DVD, the usual methods to burn to disk should work with the iso.

"Burning" to USB drive

First, download a NixOS ISO image or create a custom ISO. Then plug in a USB stick large enough to accommodate the image. Then follow the platform instructions:

From Linux

1. Find the right device with lsblk or fdisk -l. Replace /dev/sdX with the proper device in the following steps.
2. Burn with: cp nixos-xxx.iso /dev/sdX

Note: do not use /dev/sdX1 or partitions of the disk, use the whole disk /dev/sdX.

Writing the disk image with dd if=nixos.iso of=/dev/sdX bs=4M status=progress conv=fdatasync also works.

From macOS

1. Find the right device with diskutil list, let's say diskX.
2. Unmount with diskutil unmountDisk diskX.
3. Burn with: sudo dd if=path_to_nixos.iso of=/dev/diskX

Tip

Using rdiskX instead of diskX can makes a large speed difference. You can check the write speed with iostat 2 in another terminal.

From Windows

1. Download USBwriter.
2. Start USBwriter.
3. Choose the downloaded ISO as 'Source'
4. Choose the USB drive as 'Target'
5. Click 'Write'
6. When USBwriter has finished writing, safely unplug the USB drive.

Alternative installation media instructions

The previous methods are the supported methods of making the USB installation media.

Those methods are also documented, they can allow using the USB drive to boot multiple distributions. This is not supported, your mileage may vary.

• Using Unetbootin
• Manual USB Creation
• multibootusb

Booting the installation media

This article or section needs expansion.

Reason: Troubleshooting steps, and details are lacking. (Discuss in Talk:NixOS Installation Guide#)
Please consult the pedia article metapage for guidelines on contributing.

Since the installation media is hybrid, it will boot both in legacy bios mode and UEFI mode.

Whatever mode is used to boot the installation media, your motherboard or computer's configuration may need to be changed to allow booting from a Optical Disk Drive (for CD/DVD) or an external USB drive.

Legacy bios boot

This is the only boot possible on machines lacking EFI/UEFI.

UEFI boot

The EFI bootloader of the installation media is not signed and is not using a signed shim to boot. This means that Secure Boot will need to be disabled to boot.

Connecting to the internet

The installation will definitely need a working internet connection. It is possible to install without one, but the available set of packages is limited.

Wired

For network interfaces supported by the kernel, DHCP resolution should already have happened once the shell is available.

Tethered (Internet Sharing)

If you can not connect to the internet via cable or wifi, you may use smartphone's tethering capability to share internet. Depending on your smartphones capabilities, only stock kernel drivers may be required which can help providing a working network connection.

Wireless

Network Manager is installed on the graphical ISO, meaning that it is possible to use nmtui on the command line to connect to a network.

On the minimal ISO, or if you are more familiar with wpa_supplicant then you can also run wpa_passphrase ESSID | sudo tee /etc/wpa_supplicant.conf, then enter your password and systemctl restart wpa_supplicant.

Partitioning

To partition the persistent storage run sudo fdisk /dev/diskX and follow instructions for DOS or (U)EFI. A very simple example setup is given here.

DOS

• o (dos disk label)
• n new
• p primary (4 primary in total)
• 1 (partition number [1/4])
• 2048 first sector (alignment for performance)
• +500M last sector (boot sector size)
• rm signature (Y), if ex. => warning of overwriting existing system, could use wipefs
• n
• p
• 2
• default (fill up partition)
• default (fill up partition)
• w (write)

UEFI

• g (gpt disk label)
• n
• 1 (partition number [1/128])
• 2048 first sector
• +500M last sector (boot sector size)
• t
• 1 (EFI System)
• n
• 2
• default (fill up partition)
• default (fill up partition)
• w (write)

Label partitions

This is useful for having multiple setups and makes paritions easier to handle.

• lsblk
• sudo mkfs.fat -F 32 /dev/sdX1
• sudo fatlabel /dev/sdX1 NIXBOOT
• sudo mkfs.ext4 /dev/sdX2 -L NIXROOT
• sudo mount /dev/disk/by-label/NIXROOT /mnt
• sudo mkdir -p /mnt/boot
• sudo mount /dev/disk/by-label/NIXBOOT /mnt/boot

Swap file (only simple on uefi)

• sudo dd if=/dev/zero of=/mnt/.swapfile bs=1024 count=2097152 (2GB size)
• sudo chmod 600 /mnt/.swapfile
• sudo mkswap /mnt/.swapfile
• sudo swapon /mnt/.swapfile

NixOS config

• sudo nixos-generate-config --root /mnt
• cd /mnt/etc/nixos/
• sudo vim configuration.nix

Most essential changes: 1. keyboard layout, ie services.xserver.layout 2. users.users.user with adding entry initialPassword = "pw123"; 3. networking (wifi), see below for fix if it breaks 4. boot.loader.grub.device = "/dev/sda"; #or "nodev" for efi only 5. install editor to edit the configuration 6. change hardware config to use labels

NixOS installation

• cd /mnt
• sudo nixos-install

after installation: Run passwd to change user password.

if internet broke/breaks, try one of the following:

• nixos-rebuild switch --option substitute false # no downloads
• nixos-rebuild switch --option binary-caches "" # no downloads
• wpa_supplicant flags to connect to wifi

---

Additional notes for specific hardware

These are collected notes or links for specific hardware issues.

• Blog post how to install NixOS on a Dell 9560
• Brand servers may require extra kernel modules be included into initrd (boot.initrd.extraKernelModules in configuration.nix) For example HP Proliant needs "hpsa" module to see the disk drive.