Fail2ban

Fail2ban is an intrusion prevention software. It scans through log files to find signs of malicious intent. In general, Fail2ban will update the firewall rules to reject the offending IP address for a set amount of time.

Fail2Ban uses the concept of a "jail" to modularize its configuration. A jail consists of an action (such as blocking a port using iptables) that is triggered when a filter (regular expression) applied to a log file triggers/matches more than a certain number of times in a certain time period. Actions that ship with Fail2Ban are defined in /etc/fail2ban/action.d, while filters are defined in /etc/fail2ban/filter.d.

Basic Usage

Enable Fail2ban NixOS module with the expression:

  services.fail2ban.enable = true;

NixOS comes with a pre-configured SSH jail which will observe errors in the SSH daemon and ban offending IPs. If all you need is basic rate-limiting and only have the SSH port exposed, you don't have to setup anything else.

Advanced Usage

The Fail2ban NixOS module exposes various parameters for adjusting the configuration. In the following, all options mentioned are implicitly prefixed with services.fail2ban , unless specified otherwise.

The maxretry option allows you to specify how many failures are required for an IP address to be blocked.
To prevent being locked out accidentally, use ignoreIP to whitelist IPs or IP ranges to be never cheked. In the example below, common LAN IP address ranges as well as the specific IP '8.8.8.8' and the address associated with the hostname "wiki.nixos.org" are excluded from any bans. Note that the loopback addresses "127.0.0.0/8" and "::1" are added by default.
bantime specifies for how much time an IP address is blocked after reaching the maximum number of failures. Note that the bantime can be increased for every violation by setting bantime-increment.enable = true;. The bantime increment can then be customized by specifying a formula (in Python) like ban.Time * math.exp(float(ban.Count+1)*banFactor)/math.exp(1*banFactor) with bantime-increment.formula, the multipliers with bantime-increment.multipliers, the maximum bantime with bantime-increment.maxtime and the indication to consider the bans issued throughout multiple jails with bantime-increment.overalljails
banaction specifies which of the actions in /etc/fail2ban/action.d should be the default ban action (e.g., iptables, iptables-new, iptables-multiport, iptables-ipset-proto6-allports, shorewall, etc.)
extraPackages contains a list of derivations whose outputs are needed by Fail2ban actions

  services.fail2ban = {
    enable = true;
   # Ban IP after 5 failures
    maxretry = 5;
    ignoreIP = [
      # Whitelist some subnets
      "10.0.0.0/8" "172.16.0.0/12" "192.168.0.0/16"
      "8.8.8.8" # whitelist a specific IP
      "wiki.nixos.org" # resolve the IP via DNS
    ];
    bantime = "24h"; # Ban IPs for one day on the first ban
    bantime-increment = {
      enable = true; # Enable increment of bantime after each violation
      formula = "ban.Time * math.exp(float(ban.Count+1)*banFactor)/math.exp(1*banFactor)";
      multipliers = "1 2 4 8 16 32 64";
      maxtime = "168h"; # Do not ban for more than 1 week
      overalljails = true; # Calculate the bantime based on all the violations
    };
    jails = {
      apache-nohome-iptables.settings = {
        # Block an IP address if it accesses a non-existent
        # home directory more than 5 times in 10 minutes,
        # since that indicates that it's scanning.
        filter = "apache-nohome";
        action = ''iptables-multiport[name=HTTP, port="http,https"]'';
        logpath = "/var/log/httpd/error_log*";
        backend = "auto";
        findtime = 600;
        bantime  = 600;
        maxretry = 5;
      };
    };
  };

These settings are written to /etc/fail2ban/jail.local, where fail2ban will read them.

Extending Fail2ban

Fail2ban capabilities can be freely extended by adding new jails, filters, and actions; the first ones of them are already covered in the "Basic usage" section, while the other two need dedicated config files to be created in the /etc/fail2ban/filter.d and /etc/fail2ban/action.d folders.

In order to do this, you'll have to add a environment.etc section to your NixOS config file and specify there the contents of your custom actions and filters:

  environment.etc = {
    # Define an action that will trigger a Ntfy push notification upon the issue of every new ban
    "fail2ban/action.d/ntfy.local".text = pkgs.lib.mkDefault (pkgs.lib.mkAfter ''
      [Definition]
      norestored = true # Needed to avoid receiving a new notification after every restart
      actionban = curl -H "Title: <ip> has been banned" -d "<name> jail has banned <ip> from accessing $(hostname) after <failures> attempts of hacking the system." https://ntfy.sh/Fail2banNotifications
    '');
    # Defines a filter that detects URL probing by reading the Nginx access log
    "fail2ban/filter.d/nginx-url-probe.local".text = pkgs.lib.mkDefault (pkgs.lib.mkAfter ''
      [Definition]
      failregex = ^<HOST>.*(GET /(wp-|admin|boaform|phpmyadmin|\.env|\.git)|\.(dll|so|cfm|asp)|(\?|&)(=PHPB8B5F2A0-3C92-11d3-A3A9-4C7B08C10000|=PHPE9568F36-D428-11d2-A769-00AA001ACF42|=PHPE9568F35-D428-11d2-A769-00AA001ACF42|=PHPE9568F34-D428-11d2-A769-00AA001ACF42)|\\x[0-9a-zA-Z]{2})
    '');
  };

The defined filters and actions can then be used in a new jail (created as seen above):

  services.fail2ban = {
    # --- snip ---
    jails = {
      nginx-url-probe.settings = { 
        enabled = true;
        filter = "nginx-url-probe";
        logpath = "/var/log/nginx/access.log";
        action = ''%(action_)s[blocktype=DROP]
                 ntfy'';
        backend = "auto"; # Do not forget to specify this if your jail uses a log file
        maxretry = 5; 
        findtime = 600;
      }; 
    };
  };

For more details on how to develop Fail2ban filters please see the official documentation.

Basic Usage

Advanced Usage

Extending Fail2ban

See also